|
|
 |
|
TEKLITE Mains Fail Safety Lighting
Emergency
Lighting in buildings means the illumination of
exits, gangways and stairs. Now Teklite
illuminates the main area of congregation, the
place where the panic can start. Teklite
supplements and sometimes can replace other
forms of Emergency Lighting.
ACTIVATED BY MAINS FAILURE, FUSE BLOW OR SMOKE
ALARM
With
rapid warm-up, Teklite Mains Fail Safety Lamps give
up
to 6500 lumens of smoke penetrating light. Other
typical Emergency Lamps give 20 to 240 lumens.
With 25 times more light, Teklite Mains Fail Safety
Lamps
have an important place in your Emergency
Lighting System. |
AVAILABLE
MODELS FOR EASY INSTALLATION
Hang
Model Cat. 14547
Dimensions: 312
x 312 x 230mm
Weight: 8,5
kg
Wall
Model Cat. 14546
Dimensions:
240
x 218 x 200mm
Weight: 8
kg
• All
steel body construction for tough
working conditions.
• 1
hour minimum light duration.
• Sealed
maintenance-free batteries with
automatic recharge.
• Mains
and state of charge indicators with test
switch on unit or
may be fitted
remotely.
• Functional
design suits every decor.
If you are involved with, or have a
responsibility for, safety in buildings
- as architect, building inspector, fire
officer, risk assessor, or manager of
activity involving people - then TEKLITE
MAINS FAIL SAFETY LIGHTING will be of interest
to you.
TODAY,
TEKLITE TECHNOLOGY REDUCES A RISK UNTIL NOW
RECOGNISED BUT LACKING PRACTICAL SOLUTION.
|
Hang
Model Cat. 14547 |
Wall
Model Cat. 14546
|
| TECHNICAL
DETAILS |
| Lamp
Tube |
Osram
NAV-T 70 W Super or Philips SON-T 70 W |
| 220
v Supply Current |
100
mA Charging, 40 mA Standby |
| Charging
Current |
650
mA Nominal |
Battery
|
2
x 6 volt 12 Ah. Sealed Lead-acid.
Maintenance-free.
Battery
protected against deep discharge |
| Light
Output (max.) |
6500
lumens |
| Endurance |
1
hour minimum |
| Minimum
Test Time Permitted |
2
minutes |
| Charging
Time |
18
hours approximate |
|
|
|
|
IMPORTANT
Teklite
Mains Fail Safety Lamps provide a form of
Emergency Lighting until now not
realisable and therefore not yet demanded
by Regulation. They are not intended
to replace Statutory Emergency Lighting
except with the authority of the
Organisation issuing the the Fire
Certificate for the building.
However, the Area Lighting they provide is
welcomed by Fire Departments and Insurance
Companies alike, pending the eventual
possibility of new regulations making the
Area Lighting provided by this new class
of Emergency Lighting, mandatory.
|
|
All
details given here are approximate and may be subject to
change without notice. Teklite Mains Fail equipment has
been designed by the Teklite Division of Denver Technical
Products (Pty) Ltd. who reserve all rights. |
|
For
All Enquiries please
contact DENVER TECHNICAL PRODUCTS
Tel. +27 (11) 626-2023 Fax. +27 (11) 626-2009
|
|
|
|
TEKLITE
High Pressure Sodium Safety Lighting
|
• Up
to 400 watts (56 000 lumens) of yellow smoke penetrating
light.
• Metal
Halide (white light) to special order.
• 400
watts of high pressure sodium lighting is equivalent to
2500 watts of halogen light.
• Battery
duration of 1 hour (Up to 10 hours to special order).
• 2
styles - Hi Bay and Lo Bay
• Maintained
& Non-maintained types. Hi Bay & Lo Bay.
|
Lo
Bay
|
 |
LIGHT
CAN SAVE SHRINKAGE!
LIGHT CAN SAVE LIFE! |
|
|
|
APPLICATIONS:
Factories - Airports - Railway Stations - Mines - Control
Rooms - Chemical Plants - Foundries - Bakeries - Casinos -
Supermarkets - Banks - Shopping Centres - Conference Halls
FEATURES:
• Sealed
lead-acid batteries (no memory)
• Status
indication
• Battery
protected against deep discharge
• Remote
test facility
• Automatic
battery charger
• Provision
for triggering smoke alarms
• Compact
dimensions from Wall and Hang Models
|
Hi Bay
|
|
SPECIFICATIONS |
|
MAINS
FAIL OPERATION |
|
Ballast: |
Cat
No. 23383
Teklite Electronic running at
42kHZ 56K 36V 400W HPS, DC input
current 11.2A at 36V |
| Ignitor: |
Electronic
- included in ballast |
|
NORMAL
OPERATION
|
| Ballast: |
Helvar
ferro-resonant VSI 40/22-3T-D |
| Ignitor: |
Bag
Turgi NI 400L |
|
Power
factor correction capacitor or: 45uF
250V AC |
| Input
Current: |
2.4A
at 230V |
Maximum
total input current: 3.2A
(battery charging at 3A DC plus
one 400W HPS burning on
ferro-resonant ballast at 230V
50Hz.) |
|
Status
Indication |
| Red: |
Mains
On |
| Yellow: |
Battery
Charging |
| Green: |
Battery
Float |
|
Controls |
The
front panel is equipped with a
test switch. While the unit is
on stand-by, the switch should
be set to the 'ready'
position. The rear panel is
equipped with a transit switch
to prevent the unit running when
'no mains' is connected,
i.e. the mains fail relay will
detect 'no mains' if the unit is
not connected to the mains. For
normal operation, the
switch should be set to the
'normal' position.
Provision is also made for
remote test, or for connection
to smoke alarms - in which case
the mains fail safety
lamp may be remotely tested, or
triggered via a smoke alarm in
the event of a fire prior
to mains failure. |
|
Maintenance |
Teklite
Mains Fail Safety Lamps do not
contain serviceable parts. It is
only necessary to check (every
six months)
that the unit is operational.
Thus the test switch should be
operated, or the mains should be
interrupted - in which
case the second ampoule will
ignite. Provided it runs for 50
minutes, it can be assumed that
the batteries are in a
good condition. After
approximately 9 hours, the
yellow LED should extinguish and
the green LED should light
(indicating that the batteries
are again fully charged. |
|
20
MODELS AVAILABLE
- Please click here to see
table -
|
|
|
|
PRODUCT
SPECIFICATIONS |
|
MECHANICAL: |
|
Hi Bay Type 56K + 56K
Cat
No. 23367
|
| Overall
Length |
1030mm |
| Electronic
Housing |
540
x 220 x 300 + 35mm for heatsink |
| Spun
Reflector |
Dia
480 x 430mm |
| Weight |
49kg |
|
ELECTRICAL: |
|
| Charger |
Cat.
No. 23377 |
| Nominal
Voltage |
36V
DC |
| Float |
40.2V
DC |
| Max.
charge rate |
3A
DC |
| Max
AC charge current |
0.8A
at 230V 50Hz AC |
| AC
float current |
0.275A
at 230V 50Hz AC |
| Low
volt disconnect trip |
32.4V |
|
BATTERY: |
|
|
Type |
3
x 12V 18A/hr Type Yuasa NP18-12B |
|
Duration |
70
minutes to LVD cutout at 32.4V
DC |
|
LAMPS: |
|
| Type |
2
x Osram Vialox 400W NAV-T
(SON-T) |
| Light
Output |
56
000 lumens each (only 1 lamp
burns at a time) |
|
|
|
|
|
|
All Teklite
Mains Fail Safety Lighting products, are equipped with
sealed lead-acid batteries, fully automatic battery
chargers with status indication and low-volt disconnect
device - to protect the battery from deep discharge and
subsequent permanent damage. Lamps start automatically in
the event of mains failure. Battery automatically
recharges on restoration of mains supply. Lamps can also
be triggered by smoke alarms. Provision is also made for
remote testing. Battery life is expected to exceed 5
years.
|
|
TEKLITE
MAINS FAIL SAFETY LIGHTING
(Table
of Products Available) |
|
NON-MAINTAINED: |
| Cat.
No. |
Type |
Lamp
Power |
Light
Output
Lumens |
Duration
Hours |
Nominal
Battery
Voltage |
| HIGH
PRESSURE SODIUM |
| 14546 |
Wall |
70W |
6
500 |
1.25 |
12V |
| 14547 |
Hang |
70W |
6
500 |
1.25 |
12V |
| 23374 |
Wall
IP66 |
70W |
6
500 |
1.25 |
12V |
| HIGH
PRESSURE SODIUM
(Lo Bay) |
| 23354 |
7K |
70W |
6
500 |
1.25 |
12V |
| 23355 |
27K |
250W |
27
000 |
1.00 |
24V |
| 23357 |
56K |
400W |
56
000 |
1.00 |
36V |
| HIGH
PRESSURE SODIUM
(Hi Bay) |
| 23361 |
7K |
70W |
6
500 |
1.25 |
12V |
| 23362 |
27K |
250W |
27
000 |
1.00 |
24V |
| 23363 |
56K |
400W |
56
000 |
1.00 |
36V |
| METAL
HALIDE |
| 23368 |
Wall |
70W |
5
000 |
1.25 |
12V |
| 23369 |
Hang |
70W |
5
000 |
1.25 |
12V |
| METAL
HALIDE (Lo
Bay) |
| 23370 |
5K |
70W |
5
000 |
1.25 |
12.V |
|
|
| |
| MAINTAINED: |
| Cat.
No. |
Type |
Lamp
Power
Mains Fail |
Light
Power
Maintained |
Duration
Hours |
Nominal
Battery
Voltage |
| HIGH
PRESSURE SODIUM
(Lo Bay) |
| 23353 |
7K
+ 7K |
70W |
70W |
1.25 |
12V |
| 23356 |
7K
+ 27K |
70W |
250W |
1.25 |
12V |
| 23358 |
7K
+ 56K |
70W |
400W |
1.25 |
12V |
| 23359 |
27K
+ 27K |
250W |
250W |
1.00 |
24V |
| 23360 |
56K
+ 56K |
400W |
400W |
1.00 |
36V |
| HIGH
PRESSURE SODIUM
(Hi Bay) |
| 23364 |
7K
+ 7K |
70W |
70W |
1.25 |
12V |
| 23365 |
7K
+ 27K |
70W |
250W |
1.25 |
12V |
| 23350 |
7K
+ 56K |
70W |
400W |
1.25 |
12V |
| 23366 |
27K
+ 27K |
250W |
250W |
1.00 |
24V |
| 23367 |
56K
+ 56K |
400W |
400W |
1.00 |
36V |
| METAL
HALIDE |
| 23371 |
5K
+ 5K |
70W |
70W |
1.25 |
12V |
| 23372 |
5K
+ 11K |
70W |
150W |
1.25 |
12V |
| 23373 |
5K
+ 19K |
70W |
250W |
1.25 |
12V |
| 23376 |
5K
+ 35K |
70W |
400W |
1.25 |
12V |
|
|
|
|
|
All
details given here are approximate and may be subject to
change without notice. Teklite Mains Fail equipment has
been designed by the Teklite Division of Denver Technical
Products (Pty) Ltd. who reserve all rights. |
|
For
All
Enquiries please
contact DENVER TECHNICAL PRODUCTS
Tel. +27 (11) 626-2023 Fax. +27 (11) 626-2009
|
|
|
Teklite
Trailer Lamps |
 |
|
TEKLITE
Trailer Lamps
|
Teklite Trailer Lights |
|
SPECIFICATIONS |
|
Lamp Head |
4 x 1000W high pressure sodium
discharge lamps, producing a
total light output of
520 000
lumens (same as 20kW of halogen
light)
|
|
Mast |
Telescopic 8m, extended by
mechanical safety hoist. |
|
Engine |
Electric start air-cooled diesel |
|
Alternator |
6kVA |
|
Instrument Panel |
Running-time meter, frequency
meter and volt meter |
|
Trailer |
Two-wheel or four-wheel design.
Outriggers are included to
assist with levelling and
ensuring stability. The chassis
is fabricated from 76 x 38 x 6mm
steel channel and
epoxy powder
coated. The trailer hitch
incorporates an over-run brake
on the front wheels.
|
|
|
|
|
|
For
All
Enquiries please
contact DENVER TECHNICAL PRODUCTS
Tel. +27 (11) 626-2023 Fax. +27 (11) 626-2009
|
|
 |
|
SPECIFICATIONS |
|
Housing
Material |
3CR12
stainless steel
|
| Paint |
Yellow
RAL 1007 / Blue RAL 5012 / White
69-0187 powder epoxy |
| Dimensions |
242
wide x 242 deep x 930 to 1930mm |
| Weight |
17
kg |
| Light
Source |
70 watt
Metal Halide (Brilliant white
light) |
| Lamp
Performance |
5
000 lumens
|
| Battery |
24
amp per hour 12 volt sealed
lead-acid |
| Battery
Performance |
2.5
hours prior to cut-off via low
volt disconnect device, set to
trip at 9.5V. Low volt
disconnect device is included to
prevent deep discharge of
battery and consequent permanent
damage. |
| Charger
Receptacle |
Protected
by series diode. Maximum current
which can be drawn from charger
receptacle from external source:
13mA. Full battery can be
measured with a high impedance
volt meter, as a series resistor
is included to initialise the
Teklite fully automatic
three-step battery charger. |
| Battery
Charger |
6
amp automatic three-step Teklite
battery charger Type 15577 will
charge a fully discharged
battery in 10 hours. May be left
connected indefinitely, without
risk of battery damage.
Available as individual units,
grouped up to 5, or as charging
racks to charge 30 or more lamps
simultaneously (refer below for
more info). |
|
|
Mining
Shaft Inspection Lamp
|
|
|
All
details given here are approximate and may be subject to
change without notice. Teklite Mains Fail equipment has
been designed by the Teklite Division of Denver
Technical Products (Pty) Ltd. who reserve all rights. |
|
For
All
Enquiries please
contact DENVER TECHNICAL PRODUCTS
Tel. +27 (11) 626-2023 Fax. +27 (11) 626-2009
|
